In a perfect world, current that is sent along a conductive wire is supposed to reach the intended destination in full. However, this does not happen in the real world because some of the current is usually lost along the way. There are different reasons why the current gets lost along the way. In an attempt to prevent the loss of current, resistant sheathing is used to insulate conductive wires. Here are facts regarding Insulation tester.
In some cases, imperfections in cladding material allow current to leak and get lost to the surrounding. The leaking current can cause a lot of problems to the machinery and electrical circuits. That is why in order to maintain safety, the cladding needs to be tested on a regular basis. Doing this helps to identify problems before they cause equipment failure or harm people who handle the equipment through electrocution.
A cladding tester is usually used to carry out the testing. The tester tests the resistance of the insulating material to the flow of current thus, determining its integrity. There is very little loss of current for insulating materials of high quality. On the other hand, insulating materials of poor quality will allow large amounts of current to escape.
Testers measure various kinds of current when they are used to measure the quality of cladding a material is made of. The three main kinds of currents measured are capacitive, absorption, and leakage currents. Capacitive current refers to the initial burst of current that happens when voltage gets first applied to conductors.
Capacitive current can be equated to the volume of water that comes out of a pipe immediately a tap is opened. Once the tap is opened, water usually flows out at a higher rate but as the pipe gets filled with water completely, the rate drops rapidly. For the case of a conductive material, the amount of current flow drops once the conductor becomes fully charged.
Absorption current starts out very high and drops just in the same way capacitive current does. However, what differentiates the two kinds of current is the fact that absorption current drops much slowly. The storage of potential energy within the cladding is responsible for the gradual drop in absorption current. In cladding testing using time resistance method, absorption current is a very important part.
Conduction current is the other name used for leakage current. This current is present through and over the cladding and it is small and steady in nature. The increase in leakage current implies deterioration of the cladding over time as well. In insulation test meter, the rise in leakage current is indicated as a reduction in resistance.
There is a wide range of cladding testers in the market today. The various models of these products are made by manufacturers located in various countries. The quality of individual testers depends on the manufacturer of the equipment. Also, the various models of these devices in the market are used in different applications. There are testers that are meant for residential testing and those that are meant to be used in industries.
In some cases, imperfections in cladding material allow current to leak and get lost to the surrounding. The leaking current can cause a lot of problems to the machinery and electrical circuits. That is why in order to maintain safety, the cladding needs to be tested on a regular basis. Doing this helps to identify problems before they cause equipment failure or harm people who handle the equipment through electrocution.
A cladding tester is usually used to carry out the testing. The tester tests the resistance of the insulating material to the flow of current thus, determining its integrity. There is very little loss of current for insulating materials of high quality. On the other hand, insulating materials of poor quality will allow large amounts of current to escape.
Testers measure various kinds of current when they are used to measure the quality of cladding a material is made of. The three main kinds of currents measured are capacitive, absorption, and leakage currents. Capacitive current refers to the initial burst of current that happens when voltage gets first applied to conductors.
Capacitive current can be equated to the volume of water that comes out of a pipe immediately a tap is opened. Once the tap is opened, water usually flows out at a higher rate but as the pipe gets filled with water completely, the rate drops rapidly. For the case of a conductive material, the amount of current flow drops once the conductor becomes fully charged.
Absorption current starts out very high and drops just in the same way capacitive current does. However, what differentiates the two kinds of current is the fact that absorption current drops much slowly. The storage of potential energy within the cladding is responsible for the gradual drop in absorption current. In cladding testing using time resistance method, absorption current is a very important part.
Conduction current is the other name used for leakage current. This current is present through and over the cladding and it is small and steady in nature. The increase in leakage current implies deterioration of the cladding over time as well. In insulation test meter, the rise in leakage current is indicated as a reduction in resistance.
There is a wide range of cladding testers in the market today. The various models of these products are made by manufacturers located in various countries. The quality of individual testers depends on the manufacturer of the equipment. Also, the various models of these devices in the market are used in different applications. There are testers that are meant for residential testing and those that are meant to be used in industries.
About the Author:
Find details about the benefits you get when you use an insulation tester. If you have any questions, see the main page at http://www.rossengineeringcorp.com.
Aucun commentaire:
Enregistrer un commentaire