For one give the floors of any room a new look, remodeling is necessary. You can choose to hire an expert or do it yourself. You will need to have a good understanding of the place you are going to be remodeling, so, a visit to the room where you are undertaking the project is fundamental. Study the space and know the requirements and the likely challenges you are likely to face and their remedy. Remodeling mostly involves ceramic tile installation San Mateo CA.
Most people will do remodeling of floors using slates. Some floors are made of asbestos whose fibers when inhaled can cause lung cancer. This shows the purpose of studying the area before commencing the project. When aware of the dangers you are likely to encounter, take precautions. Wearing a gas mask will prevent you from breathing the fiber. Carry goggles to protect the eyes and leather gloves for the hands.
Also, you need other tools like a square that is mainly used by carpenters, a tape measure, and a bubble level. Slate cutter, a notched trowel, sealant, grout, and a puff knife are also essential. With these tools ready, the next step is to begin the job.
Some floors make it difficult to lay ceramic slates since some are made of plywood immediately below the top cover. If you come across such a case, it is good first to prepare a layer separating the shingles and the hardwood to prevent moisture from reaching the wood. Better flooring is one that has a strong subflooring, and whether wooden or concrete, subflooring should be able to support the tiles so that they do not break. Floors that are made of concrete are easy to install tiles.
When the subflooring is complete, be keen to mark the point at the center of the area you measure since it is the point where you start the slate installation. From the mark you have made, use the tape measure to get the length across the room from all directions. Start laying the pantiles at the designated location.
The first tile should be placed very carefully to ensure it falls in the right location. The purpose of the notched trowel comes in at this step. It is used to apply adhesive to the tile on the floor. After smearing, place the shingle carefully and then use force and a little twisting for the slate to be firm on the surface.
Some adhesive will escape through the sides when twisting the slate to level it with the ground. Use a piece of cloth to wipe it off before dying. Repeat what has been done to the first pantile to all pantiles till the whole floor gets covered.
Having placed the first shingles, others that follow take short to complete. When done, use rubber grout float to apply the grout or mixed cement to cover the gaps between the pantiles. The project is completed when you let the tiles dry and cover them. When uncovering, you will get a new face of your floor.
Most people will do remodeling of floors using slates. Some floors are made of asbestos whose fibers when inhaled can cause lung cancer. This shows the purpose of studying the area before commencing the project. When aware of the dangers you are likely to encounter, take precautions. Wearing a gas mask will prevent you from breathing the fiber. Carry goggles to protect the eyes and leather gloves for the hands.
Also, you need other tools like a square that is mainly used by carpenters, a tape measure, and a bubble level. Slate cutter, a notched trowel, sealant, grout, and a puff knife are also essential. With these tools ready, the next step is to begin the job.
Some floors make it difficult to lay ceramic slates since some are made of plywood immediately below the top cover. If you come across such a case, it is good first to prepare a layer separating the shingles and the hardwood to prevent moisture from reaching the wood. Better flooring is one that has a strong subflooring, and whether wooden or concrete, subflooring should be able to support the tiles so that they do not break. Floors that are made of concrete are easy to install tiles.
When the subflooring is complete, be keen to mark the point at the center of the area you measure since it is the point where you start the slate installation. From the mark you have made, use the tape measure to get the length across the room from all directions. Start laying the pantiles at the designated location.
The first tile should be placed very carefully to ensure it falls in the right location. The purpose of the notched trowel comes in at this step. It is used to apply adhesive to the tile on the floor. After smearing, place the shingle carefully and then use force and a little twisting for the slate to be firm on the surface.
Some adhesive will escape through the sides when twisting the slate to level it with the ground. Use a piece of cloth to wipe it off before dying. Repeat what has been done to the first pantile to all pantiles till the whole floor gets covered.
Having placed the first shingles, others that follow take short to complete. When done, use rubber grout float to apply the grout or mixed cement to cover the gaps between the pantiles. The project is completed when you let the tiles dry and cover them. When uncovering, you will get a new face of your floor.
About the Author:
Find a summary of the benefits of using ceramic tile installation San Mateo CA services and more info about a knowledgeable tiling contractor at http://www.stewarttile.com/fullwidth today.
Aucun commentaire:
Enregistrer un commentaire